For VATSIM controllers
Turn a dial. Push.
Cleared.
Scope Deck is the Stream Deck built for controllers. Clear the selected aircraft to an altitude, heading or speed, zoom the scope, work your frequencies and take or hand off traffic, without leaving the scope. EuroScope, CRC and vatSys.
$17.96 (was $19.95) · Stream Deck, +, XL and + XL · No serial
Instruction video
Learn it in three minutes
How the dials work
Turn to pick, push to send
Click an aircraft on your scope. The deck shows its callsign, cleared level and heading as live data blocks. Then:
Turn to pick
The value glows amber on the key until you send it. 1,000 ft, 5 degrees or 10 knots a click.
Push to send
One push and the clearance goes to the selected aircraft.
Press and turn
Fine steps: 100 ft, 1 degree, 5 knots.
Touch to cancel
Touch the screen to drop the pick; touch and hold to clear a heading or speed. The pick also drops after 8 seconds or when you select another aircraft.
What it does
Every move a busy sector needs
Altitude, heading, speed, Mach
Dials on the Stream Deck +, keys on every Stream Deck. Flight levels above the transition altitude, feet below, plus ILS and visual approach clearances.
Range and zoom
Zoom the scope in and out and re-centre it with the RANGE dial or the zoom keys, on EuroScope, CRC and vatSys.
Direct-to
Step through the next points on the route and clear the aircraft direct with one push.
Handoffs you never miss
Assume, release, hand off, accept and refuse. A handoff offered to you flashes red on HANDOFF and ACCEPT.
Your frequencies
With TrackAudio: push-to-talk, RX and TX per frequency, volume, and the last caller lit on the deck. Press it to select that aircraft.
CRC keys
ERAM QZ, QQ, QT, QX and QP; STARS initiate, terminate, handoff and multifunction; flight plan editor, messages and four bookmarks.
Works with your controller client
EuroScope, CRC, vatSys and TrackAudio
EuroScope 3.2
Two-wayThe included CTC Scope Link plug-in reads the aircraft you select and sets the cleared level, heading, speed, Mach, direct-to and tracking. Load it once from OTHER SET > Plug-ins. It talks only to the deck on your own PC.
CRC (vNAS)
ERAM and STARSNothing to install. The deck types the real commands (QZ 240, QS 270, +110 ...) and you click the target, or press LAST CALLER first and it goes straight to that callsign.
vatSys
Scope keysZoom, range and the client keys.
TrackAudio
VoiceNothing to install. Start TrackAudio and the RADIO page finds it on its own.
The pages
Modern glass keys, live data blocks
Profiles for the Stream Deck, Stream Deck +, XL and + XL. Click a picture to see it bigger.
Control on VATSIM? Get it free.
Use Scope Deck on a live stream or show it off in a Facebook post, and we'll get it to you at no charge.
1. Stream it or post it
Use Scope Deck on your Twitch, YouTube or Kick stream while you control, or post it on Facebook.
2. Open a ticket
In our Discord, with your VATSIM CID and the link to your channel or your post.
3. Get your deck
We send you the full deck: every page and every profile, the same as the paid version.
Setup
Ready in two minutes
- 1Double-click the .streamDeckPlugin file. Stream Deck installs it with the profiles for your Stream Deck.
- 2EuroScope: OTHER SET > Plug-ins > Load, pick CTCScopeLink.dll, and allow it on every ASR. Type .ctc in the command line to see the link.
- 3CRC: nothing to install. Keep the ERAM or STARS window in front.
- 4TrackAudio: nothing to install. Start it and the RADIO page finds it.
- 5Set your transition altitude in any key's settings, and leave SCOPE CLIENT on AUTO.
Requirements
- Windows 10 or 11
- Elgato Stream Deck software 6.9 or newer
- Stream Deck, Stream Deck +, Stream Deck XL or Stream Deck + XL
- EuroScope 3.2 (plug-in included), CRC (vNAS) or vatSys
- TrackAudio for the voice keys (optional)
- No serial needed
Questions
FAQ
Does it work without a Stream Deck +?
Yes. The Stream Deck, XL and + XL profiles have altitude, heading and speed up / down keys and a SEND key in place of the dials.
Does the EuroScope plug-in send anything to the network?
No. It listens on your own PC only (127.0.0.1) and does what you would do with the mouse in EuroScope's own tag menus.
Which transition altitude does it use?
6,000 ft for EuroScope and 18,000 ft for CRC out of the box. Change it in any key's settings to match your FIR.
Which scope client do I pick?
Leave the SCOPE CLIENT key on AUTO: it uses EuroScope while the link is running and CRC ERAM otherwise. Or pick EuroScope, CRC ERAM, CRC STARS or vatSys.
CTC Scope Deck · $17.96 (was $19.95)
Every page, every profile. Custom hand-built by ClearedToCode.
Get Scope Deck · $17.96 (was $19.95)Independent add-on. Not affiliated with or endorsed by VATSIM, EuroScope, vNAS / CRC, vatSys, TrackAudio or Elgato. Names are trademarks of their owners.
